Centimeter to Inch Converter
Convert centimeters to inches with our free online length converter.
Quick Answer
1 Centimeter = 0.393701 inches
Formula: Centimeter × conversion factor = Inch
Use the calculator below for instant, accurate conversions.
Our Accuracy Guarantee
All conversion formulas on UnitsConverter.io have been verified against NIST (National Institute of Standards and Technology) guidelines and international SI standards. Our calculations are accurate to 10 decimal places for standard conversions and use arbitrary precision arithmetic for astronomical units.
Centimeter to Inch Calculator
How to Use the Centimeter to Inch Calculator:
- Enter the value you want to convert in the 'From' field (Centimeter).
- The converted value in Inch will appear automatically in the 'To' field.
- Use the dropdown menus to select different units within the Length category.
- Click the swap button (⇌) to reverse the conversion direction.
How to Convert Centimeter to Inch: Step-by-Step Guide
Converting Centimeter to Inch involves multiplying the value by a specific conversion factor, as shown in the formula below.
Formula:
1 Centimeter = 0.393701 inchesExample Calculation:
Convert 10 centimeters: 10 × 0.393701 = 3.937008 inches
Disclaimer: For Reference Only
These conversion results are provided for informational purposes only. While we strive for accuracy, we make no guarantees regarding the precision of these results, especially for conversions involving extremely large or small numbers which may be subject to the inherent limitations of standard computer floating-point arithmetic.
Not for professional use. Results should be verified before use in any critical application. View our Terms of Service for more information.
Need to convert to other length units?
View all Length conversions →What is a Centimeter and a Inch?
The centimeter (symbol: cm) is a unit of length equal to exactly one-hundredth of a meter (1/100 m or 0.01 m). It's also equal to exactly 10 millimeters.
The centimeter is part of the International System of Units (SI) and uses the metric prefix "centi-" meaning one-hundredth (from Latin centum, "hundred").
Mathematical Relationships
1 centimeter equals:
- 10 millimeters (mm)
- 0.01 meters (m)
- 0.00001 kilometers (km)
- 0.393701 inches (in)
- 0.0328084 feet (ft)
Key conversion:
- 1 inch = 2.54 cm exactly (this is the official international definition established in 1959)
Why Centimeters?
While the meter is the official SI base unit for length, centimeters are more practical for everyday measurements:
Too small for meters, too large for millimeters: A person who is 1.75 meters tall is more commonly described as 175 centimeters in metric countries. Writing "1.75 m" requires decimals; "175 cm" uses whole numbers.
Human-scale convenience: Most objects people interact with daily—clothing, screens, body measurements, food items—fall naturally into the 1-100 cm range.
Avoids decimal confusion: "15.2 cm" is clearer than "0.152 m" for most people.
The inch is a unit of length in the British imperial and United States customary systems of measurement. Since the international yard and pound agreement of 1959, one inch has been defined as exactly 2.54 centimeters. This makes the inch equal to 1/12 of a foot, 1/36 of a yard, and 25.4 millimeters precisely.
The inch is denoted by the symbol in or by a double prime mark ″ (e.g., 5″ means 5 inches). In engineering drawings and construction blueprints, dimensions are typically expressed in feet and inches (e.g., 5′-3″ means 5 feet, 3 inches).
Unlike the metric system with its consistent decimal relationships, the inch exists within a complex system where 12 inches make a foot, 3 feet make a yard, and 1,760 yards make a mile. This fractional system reflects the inch's origins in human-scale measurements rather than mathematical convenience.
Note: The Centimeter is part of the metric (SI) system, primarily used globally in science and trade. The Inch belongs to the imperial/US customary system.
History of the Centimeter and Inch
French Revolution and the Birth of the Metric System
1790s: Revolutionary Innovation: The centimeter was born from the French Revolution's ambition to create a rational, universal measurement system based on nature and decimal mathematics.
The Meter Foundation: In 1791, the French Academy of Sciences defined the meter as one ten-millionth (1/10,000,000) of the distance from the equator to the North Pole along the meridian passing through Paris. The centimeter automatically followed as 1/100 of this meter.
Latin Roots: The prefix "centi-" derives from the Latin centum (hundred), making "centimeter" literally "hundredth of a meter."
1795 Official Adoption: France officially adopted the metric system on April 7, 1795, including the centimeter as a standard subdivision of the meter.
CGS System: The Centimeter's Scientific Era
1874: The Centimeter-Gram-Second System: British scientists James Clerk Maxwell and William Thomson (Lord Kelvin) promoted the CGS system, which used:
- Centimeter for length (instead of meter)
- Gram for mass (instead of kilogram)
- Second for time
Scientific Dominance: The CGS system became the preferred standard for physics and chemistry throughout the late 19th and early 20th centuries. Many scientific formulas and units were developed using centimeters.
Legacy Units: Several units still reflect the CGS heritage:
- Poise (viscosity): measured in gram/(centimeter·second)
- Erg (energy): gram·centimeter²/second²
- Gauss (magnetic field): CGS unit for magnetic flux density
Transition to SI and the Modern Era
1960: The SI System: The International System of Units (SI) was officially established, promoting the meter-kilogram-second (MKS) system instead of CGS.
Centimeter's Continued Relevance: Despite the official SI preference for meters, centimeters remained dominant for everyday measurements because:
- They're more practical for human-scale objects
- They avoid decimals for most common measurements
- They're familiar and intuitive
Global Adoption: Today, 195 of 198 countries use the metric system, with centimeters as the standard for body height, clothing, and everyday measurements. Only the United States, Myanmar, and Liberia officially use non-metric systems.
The inch has one of the longest continuous histories of any modern measurement unit, with roots stretching back over two millennia.
Ancient Origins: The Roman "uncia" (meaning one-twelfth) represented 1/12 of a Roman foot, similar to our modern inch. When the Romans occupied Britain, they brought this measurement system with them, establishing a tradition that would last far beyond their empire.
Medieval Definitions: Throughout the Middle Ages, various rulers attempted to standardize the inch using body-based measurements. King Edward I of England ordered in 1305 that an inch should equal the length of three barleycorns (grains of barley) laid end to end. King Edward II formalized this in 1324, making it English law. Other definitions included the width of a man's thumb at the base of the nail.
Regional Variations: Before standardization, different regions maintained slightly different inch measurements. The Tower inch, Merchant's inch, and Cloth inch all differed slightly, causing confusion in trade and construction. The French pouce (thumb) was approximately 1.066 English inches.
1959 International Agreement: The modern inch was defined by the international yard and pound agreement signed by the United States, United Kingdom, Canada, Australia, New Zealand, and South Africa. They agreed that 1 yard equals exactly 0.9144 meters, making 1 inch exactly 2.54 centimeters. This ended centuries of slight variations and created perfect mathematical alignment between imperial and metric systems.
US Survey Inch: For a time, the US maintained two slightly different inches—the international inch (2.54 cm exactly) and the US survey inch (2.540005080010160020 cm, based on the Mendenhall Order of 1893). As of January 1, 2023, the US officially retired the survey inch, making all American measurements use the international inch exclusively.
Common Uses and Applications: centimeters vs inches
Explore the typical applications for both Centimeter (metric) and Inch (imperial/US) to understand their common contexts.
Common Uses for centimeters
Medical and Healthcare
Growth Charts: Children's height is tracked in centimeters from birth:
- Pediatricians plot growth on percentile charts
- Birth length recorded in cm (typically 45-55 cm)
- Annual height measurements track development
Medical Measurements:
- Wound size: "3 cm laceration"
- Tumor diameter: measured in cm for staging
- Organ size: "enlarged liver extending 4 cm below rib cage"
- Dilation during childbirth: measured in cm (0-10 cm)
Medical Equipment:
- Blood pressure cuff width: 12-13 cm for adults
- Surgical incision length: documented in cm
- Catheter diameter: measured in mm, length in cm
Education and School Supplies
Rulers and Measuring Tools: Most rulers worldwide show centimeters:
- Standard ruler: 15 cm or 30 cm length
- Meter stick: 100 cm with cm markings
- Tape measures: marked in cm (and meters)
Paper Sizes (International ISO 216 Standard):
- A4 paper: 21 × 29.7 cm (most common worldwide)
- A5 paper: 14.8 × 21 cm (half of A4)
- A3 paper: 29.7 × 42 cm (double A4)
- Letter size (US): 21.6 × 27.9 cm (8.5 × 11 inches)
School Supplies:
- Pencil length: 19 cm (new)
- Notebook width: 15-21 cm
- Eraser length: 4-6 cm
Construction and Home Improvement
Tile Sizes: Floor and wall tiles measured in cm:
- Small tiles: 10×10 cm
- Medium tiles: 30×30 cm
- Large format tiles: 60×60 cm or 80×80 cm
- Subway tiles: 7.5×15 cm
Furniture Dimensions:
- Coffee table height: 40-50 cm
- Dining table height: 75 cm (standard)
- Chair seat height: 45-50 cm
- Sofa seat depth: 50-60 cm
Door Measurements:
- Standard interior door width: 80-90 cm
- Standard door height: 200-210 cm
- Door thickness: 3.5-4.5 cm
Art, Design, and Photography
Photo Print Sizes:
- 10×15 cm (4×6 inches) - standard print
- 13×18 cm (5×7 inches)
- 20×25 cm (8×10 inches)
- 30×40 cm (12×16 inches)
Canvas and Frame Sizes: Art supply stores sell in metric:
- Small canvas: 20×25 cm
- Medium canvas: 30×40 cm
- Large canvas: 50×70 cm
Drawing and Design:
- Technical drawings: dimensioned in cm or mm
- Graph paper: 0.5 cm or 1 cm grids
- Architectural scales: often use 1:50 or 1:100 (cm-based)
Sports and Recreation
Swimming Pool Depth: Measured in cm or meters:
- Shallow end: 90-120 cm
- Deep end: 180-300 cm
- Competition pool depth: minimum 200 cm
Bicycle Frame Sizes: Road bikes measured in cm:
- Small frame: 48-52 cm
- Medium frame: 54-56 cm
- Large frame: 58-62 cm
Sports Equipment:
- Tennis ball diameter: 6.5-6.7 cm
- Golf ball diameter: 4.3 cm
- Basketball diameter: 24 cm
When to Use inches
Home Construction and Renovation
Residential construction in the United States operates almost exclusively in inches and feet. Standard framing uses 16-inch or 24-inch on-center stud spacing, creating modular dimensions that align with 48-inch-wide drywall and plywood sheets. Contractors calculate materials in board feet and square footage, but individual measurements are precise to 1/16 inch.
Kitchen cabinets come in 3-inch width increments (12″, 15″, 18″, 21″, 24″, 27″, 30″, 33″, 36″), with standard depth of 24 inches for base cabinets and 12 inches for wall cabinets. Countertop height standardizes at 36 inches, while bar counters sit at 42 inches. These dimensions have remained unchanged for decades, creating an entire ecosystem of compatible fixtures, appliances, and hardware.
Tile installation relies on precise inch measurements. Floor tiles commonly measure 12″ × 12″, 12″ × 24″, or 24″ × 24″. Wall tiles might be 3″ × 6″ subway tiles or 4″ × 4″ ceramic squares. Grout line spacing typically runs 1/16″ to 1/4″ depending on tile type. Tile setters work to extremely tight tolerances, as even 1/16-inch variation across a room becomes visibly noticeable.
Manufacturing and Machining
American manufacturing maintains imperial measurements for historical and practical reasons. Machine shops operate in decimal inches (0.001″ = 1 "thou" or 1 "mil"), with precision machining achieving tolerances of ±0.0001″ (one ten-thousandth of an inch, called a "tenth").
Thread specifications use threads per inch (TPI): 1/4″-20 means a 1/4-inch diameter bolt with 20 threads per inch. Common thread pitches include coarse (UNC) and fine (UNF) standards, with sizes ranging from #0-80 (tiny electronic screws) to several inches in diameter for industrial equipment.
Sheet metal thickness traditionally uses gauge numbers (inversely related to thickness in inches). 20-gauge steel is approximately 0.036 inches thick, while 10-gauge is 0.135 inches. However, modern manufacturing increasingly specifies thickness in decimal inches (0.063″ aluminum sheet) for clarity.
CNC (Computer Numerical Control) machines can work in either inches or millimeters, but American shops predominantly program in inches. A machinist might bore a hole to 0.5005″ diameter to accept a 1/2-inch precision shaft with 0.0005″ clearance.
Fasteners and Hardware
The American fastener industry operates entirely in imperial measurements. Screw and bolt diameters are specified in fractions (1/4″, 5/16″, 3/8″, 1/2″) or gauge numbers (#4, #6, #8, #10). Thread pitch is given in threads per inch.
Common bolt sizes and their applications:
- 1/4″-20: Electronics, light fixtures, small brackets
- 5/16″-18: Medium structural connections, automotive
- 3/8″-16: Heavy brackets, machinery, automotive chassis
- 1/2″-13: Structural steel, heavy machinery, trailer hitches
- 5/8″-11: Building construction, large structural connections
- 3/4″-10: Industrial equipment, heavy structural steel
Hex keys (Allen wrenches) come in fractional inch sizes: 1/16″, 5/64″, 3/32″, 1/8″, 5/32″, 3/16″, 7/32″, 1/4″, 5/16″, and 3/8″. Metric hex keys are incompatible—a 5mm key is 0.197″, close to but not quite matching 3/16″ (0.1875″) or 1/4″ (0.25″).
Display Technology and Photography
Television and monitor sizes are universally described by screen diagonal in inches, even in metric countries. This convention originated with cathode ray tubes, where the diagonal measurement corresponded to the visible screen area inside the bezel.
Common display sizes and their uses:
- 24″ monitors: Standard office workstation
- 27″ monitors: Popular desktop size, ideal for 1440p resolution
- 32″ monitors: Large desktop or small TV
- 43″ TVs: Small bedroom TV
- 55″ TVs: Most popular living room size
- 65″ TVs: Premium living room standard
- 75″ TVs: Home theater
- 85″+ TVs: Luxury home cinema
Photography inherited imperial measurements from early camera equipment. Sensor sizes reference inches in confusing ways—a "1-inch sensor" is actually much smaller (13.2 × 8.8 mm), referencing the outer diameter of an obsolete video camera tube rather than the actual sensor dimensions.
Large format photography uses inch measurements directly: 4×5″ and 8×10″ sheet film, or medium format 6×4.5cm, 6×6cm, 6×7cm (which are actually metric despite being called 120 film).
Plumbing and Pipe Systems
Plumbing pipe sizes in the US use nominal measurements that don't match actual dimensions. A "1/2-inch pipe" has an inside diameter of approximately 0.622″ and outside diameter of 0.840″. This naming convention dates back to when pipe walls were much thicker.
Common pipe sizes and uses:
- 1/2″ nominal: Standard water supply lines to fixtures
- 3/4″ nominal: Main water supply within house
- 1″ nominal: Supply from water meter to house
- 1½″ nominal: Sink drain lines
- 2″ nominal: Toilet drain, main stack
- 3″ nominal: Main drain, sewer connection
- 4″ nominal: Main building drain and sewer
Copper pipe uses different sizing: Type M, L, and K copper all have the same outside diameter for a given size, but different wall thicknesses. PEX (cross-linked polyethylene) tubing uses actual measurements—1/2″ PEX has a 0.500″ outside diameter.
Weather Reporting and Climatology
United States weather forecasting measures precipitation in inches. The National Weather Service issues warnings based on inch thresholds:
- Flash Flood Watch: Expected 1-2 inches in one hour or 3-4 inches in several hours
- Heavy Snow Warning: 6+ inches in 12 hours or 8+ inches in 24 hours
- Blizzard Warning: 3+ hours of heavy snow with sustained winds 35+ mph
Rainfall intensity rates:
- Light rain: <0.10 inches per hour
- Moderate rain: 0.10 to 0.30 inches per hour
- Heavy rain: >0.30 inches per hour
Annual precipitation varies dramatically across the US:
- Las Vegas, NV: 4.2 inches per year (desert)
- Phoenix, AZ: 8.3 inches per year
- Los Angeles, CA: 14.9 inches per year
- New York, NY: 46.2 inches per year
- Seattle, WA: 37.5 inches per year
- Miami, FL: 61.9 inches per year
- Mobile, AL: 67.0 inches per year (wettest major US city)
- Mt. Waialeale, HI: 450+ inches per year (one of Earth's wettest places)
Automotive and Cycling
American automotive specifications traditionally use inches:
- Wheel Diameter: 15″, 16″, 17″, 18″, 19″, 20″, 22″ (passenger vehicles)
- Tire Width: Given in millimeters, but wheel size in inches (e.g., 225/65R17)
- Ground Clearance: Often stated in inches (e.g., 8.6″ clearance)
- Cargo Space: Cubic feet, with dimensions in inches
- Engine Displacement: Historically cubic inches (350 cu in = 5.7L), now usually liters
Bicycle sizing uses a mix of systems. Mountain bike wheels measure 26″, 27.5″ (650B), or 29″ in diameter. Road bikes use the 700c standard (approximately 27″ diameter, derived from French sizing). Frame sizes might be given in inches (17″ mountain bike) or centimeters (56cm road bike) depending on manufacturer and tradition.
HVAC and Duct Work
Heating, ventilation, and air conditioning (HVAC) systems in the US specify duct sizes in inches. Rectangular ductwork might be 6″ × 10″, 8″ × 12″, or 10″ × 16″. Round ducts come in 4″, 6″, 8″, 10″, and 12″ diameters.
Air register and vent sizes are standardized in inches:
- Floor registers: 4″ × 10″, 4″ × 12″, 4″ × 14″
- Wall registers: 6″ × 10″, 6″ × 12″, 8″ × 10″
- Return air grilles: 14″ × 24″, 16″ × 20″, 20″ × 20″
Furnace filters use inch sizing: 16″ × 20″ × 1″, 16″ × 25″ × 1″, 20″ × 25″ × 4″. The first two dimensions are the face size, and the third is the thickness. Standard filters are 1″ thick, while pleated media filters might be 4″ or 5″ thick for better filtration and airflow.
Additional Unit Information
About Inch (in)
How many inches are in a foot?
There are exactly 12 inches in one foot. This relationship is fixed by definition in the US customary and imperial systems. The division of a foot into 12 parts dates back to ancient Roman measurements and remained standard because 12 is easily divisible by 2, 3, 4, and 6—making fractional measurements convenient in practical applications.
To convert feet to inches, multiply by 12. To convert inches to feet, divide by 12.
- 5 feet = 5 × 12 = 60 inches
- 48 inches = 48 ÷ 12 = 4 feet
- 3 feet 7 inches = (3 × 12) + 7 = 43 inches total
How many centimeters are in an inch?
One inch equals exactly 2.54 centimeters. This relationship was established by the 1959 international yard and pound agreement, which defined the yard as exactly 0.9144 meters. Since one inch equals 1/36 of a yard, it works out to precisely 2.54 cm.
This is one of the few perfectly defined relationships between imperial and metric systems. There's no rounding or approximation—it's exactly 2.54000... cm per inch by international agreement.
To convert inches to centimeters, multiply by 2.54. To convert centimeters to inches, divide by 2.54.
- 10 inches = 10 × 2.54 = 25.4 cm
- 50 cm = 50 ÷ 2.54 = 19.685 inches
Why does the US still use inches instead of the metric system?
The United States remains one of only three countries (along with Myanmar and Liberia) not officially using the metric system, largely due to historical momentum, infrastructure costs, and cultural identity.
Infrastructure Investment: The US has trillions of dollars invested in imperial-based infrastructure—road signs showing miles, construction materials in feet and inches, manufacturing equipment calibrated in thousandths of an inch, pipelines in inch diameters, and billions of blueprints in feet-inches notation. Converting all of this would cost an estimated $370 billion to $1 trillion.
Industry Standardization: American manufacturing, construction, and engineering have perfected systems around imperial measurements over centuries. Millions of workers are trained in inches and feet. Changing would require retraining entire industries and replacing countless tools, gauges, and documentation.
Cultural Resistance: Americans intuitively understand inches, feet, and miles from childhood. Polls consistently show that most Americans oppose mandatory metric conversion, viewing it as unnecessary government overreach. Unlike temperature (where Fahrenheit provides finer granularity for weather), length measurements in inches don't provide any practical advantage—but changing feels like abandoning tradition.
Failed Conversion Attempts: Congress passed the Metric Conversion Act in 1975, making metric the "preferred system" but keeping adoption voluntary. Without enforcement, industries continued using imperial. A 1982 push to convert road signs to kilometers was abandoned after fierce public backlash.
Partial Adoption: The US actually uses metric extensively in science, medicine, military, and some industries. All US customary units are now legally defined in terms of metric units. Americans live in a hybrid system—drinking 2-liter sodas while driving 65 miles per hour.
What's the difference between decimal inches and fractional inches?
Fractional inches express measurements as common fractions: 1/2″, 3/4″, 5/8″, 7/16″, 15/32″. This system dominates carpentry, construction, and mechanical work. Rulers and tape measures show fraction markings—typically down to 1/16″ for standard use and 1/32″ for precision carpentry.
Decimal inches express measurements as decimal values: 0.5″, 0.75″, 0.625″, 0.4375″, 0.46875″. Engineering drawings, machining, and manufacturing prefer decimals because they're easier to calculate with, especially for tolerances and fits.
Both systems describe the same measurements:
- 1/2″ = 0.500″
- 3/4″ = 0.750″
- 5/8″ = 0.625″
- 1/8″ = 0.125″
Machine shops often work in "thousandths" (0.001″, called a "thou" or "mil") for precision. A machinist might drill a 0.257″ diameter hole—trying to express this as a fraction (257/1000″) would be impractical.
Carpenters and builders work in fractions because tape measures show fractions, and because halving measurements repeatedly (1/2, 1/4, 1/8, 1/16, 1/32) is natural in layout work.
How accurate is an inch measurement?
The definition of an inch is exact: 2.54 centimeters precisely, or 25.4 millimeters. There's no uncertainty in the standard itself.
Practical accuracy depends on the measuring tool:
- Ruler or tape measure: Accurate to roughly ±1/16″ (±1.6 mm) for careful work
- Steel ruler with machinist's markings: ±1/32″ (±0.8 mm) when read carefully
- Dial calipers: ±0.001″ (±0.025 mm) typical accuracy
- Digital calipers: ±0.0005″ (±0.013 mm) for quality instruments
- Micrometers: ±0.0001″ (±0.0025 mm) for precision tools
- Coordinate measuring machines (CMM): ±0.00005″ (±0.0013 mm) or better
Different trades require different precision:
- House framing: ±1/8″ is usually acceptable
- Finish carpentry: ±1/16″ or better for visible joints
- Cabinetmaking: ±1/32″ for tight-fitting doors and drawers
- Machining: ±0.001″ (one thousandth) for standard fits
- Precision machining: ±0.0001″ (one ten-thousandth, called a "tenth")
- Gauge blocks (calibration standards): Accurate to millionths of an inch
Can I use a metric wrench on an inch bolt?
Generally no—metric and imperial fasteners are incompatible. While some sizes appear close, using the wrong wrench damages bolt heads and nuts.
Why they're incompatible: Metric sockets and wrenches are sized in millimeters (8mm, 10mm, 13mm, 17mm), while imperial fasteners use fractional inches (5/16″, 3/8″, 1/2″, 5/8″). These don't align:
- 13mm = 0.512″ (close to 1/2″ = 0.500″, but not exact)
- 10mm = 0.394″ (between 3/8″ = 0.375″ and 7/16″ = 0.438″)
The result: A 13mm wrench on a 1/2″ bolt will be 0.012″ too large—enough to round off the hex corners with sufficient force. A 10mm wrench on a 3/8″ bolt won't fit at all.
Exception: In an emergency, you might carefully use a slightly large adjustable wrench or locking pliers, but this risks damaging the fastener. Always use the correct system—if you work on American-made equipment, you need inch tools. For European or Japanese equipment, you need metric tools.
Many professional mechanics maintain complete sets of both imperial and metric sockets, wrenches, and hex keys—a significant investment but essential for working on diverse equipment.
What does the ″ symbol mean?
The double prime symbol ″ represents inches in technical drawings, blueprints, and mathematical contexts. A single prime ′ represents feet.
Standard notation:
- 5′ = five feet
- 5″ = five inches
- 5′-3″ = five feet, three inches
- 5′-3½″ = five feet, three and a half inches
Origin: These symbols come from astronomical and geometric notation, where they represented divisions of degrees (°). A degree divided by 60 gives minutes (′), and a minute divided by 60 gives seconds (″). This notation was borrowed for feet and inches because of the similar subdividing relationship.
Common substitution: Because typewriters and keyboards lack easy access to proper prime symbols, people often substitute:
- Apostrophe (') for feet: 5' tall
- Quotation mark (") for inches: 5" wide
- Both together: 5'-3" tall
In professional CAD drawings and blueprints, proper prime symbols (′ and ″) are standard. In casual writing, apostrophes and quotes are acceptable and universally understood.
How is screen size measured in inches?
Display screen sizes (TVs, monitors, tablets, smartphones) are always measured diagonally from one corner to the opposite corner, measuring only the visible screen area (not the bezel or frame).
Why diagonal? This convention originated with cathode ray tubes (CRTs), where the diagonal measurement corresponded to the size of the round tube face. When rectangular screens became standard, the diagonal measurement convention persisted for consistency.
Practical dimensions for common sizes:
TVs (16:9 aspect ratio):
- 55″ diagonal = approximately 48″ wide × 27″ tall
- 65″ diagonal = approximately 56.7″ wide × 31.9″ tall
- 75″ diagonal = approximately 65.4″ wide × 36.8″ tall
Monitors (16:9 aspect ratio):
- 24″ diagonal = approximately 20.9″ wide × 11.8″ tall
- 27″ diagonal = approximately 23.5″ wide × 13.2″ tall
Why this matters: When planning where to place a TV or monitor, you need the actual width and height, not the diagonal. Always check specifications for exact dimensions. Also add 1-2 inches in each direction to account for the bezel.
How do I convert inches to millimeters?
To convert inches to millimeters, multiply by 25.4. This gives you an exact result because the inch is legally defined as exactly 2.54 centimeters (25.4 millimeters).
Formula: millimeters = inches × 25.4
Examples:
- 1 inch = 1 × 25.4 = 25.4 mm
- 2 inches = 2 × 25.4 = 50.8 mm
- 0.5 inches = 0.5 × 25.4 = 12.7 mm
- 10 inches = 10 × 25.4 = 254 mm
- 3.25 inches = 3.25 × 25.4 = 82.55 mm
Converting fractional inches: First convert the fraction to a decimal, then multiply by 25.4:
- 1/2″ = 0.5″ = 0.5 × 25.4 = 12.7 mm
- 3/4″ = 0.75″ = 0.75 × 25.4 = 19.05 mm
- 5/8″ = 0.625″ = 0.625 × 25.4 = 15.875 mm
- 1/8″ = 0.125″ = 0.125 × 25.4 = 3.175 mm
Reverse conversion (mm to inches): Divide millimeters by 25.4:
- 50 mm = 50 ÷ 25.4 = 1.969 inches (approximately 2 inches)
- 100 mm = 100 ÷ 25.4 = 3.937 inches (approximately 4 inches)
For quick mental estimates, remember that 25mm ≈ 1 inch. This gives you approximately correct values for rough planning, though it slightly underestimates (25mm is actually 0.984 inches).
Why are lumber dimensions not the actual size?
Lumber in the United States is sold using nominal dimensions—traditional names that don't match the actual milled size. A "2×4" is actually 1.5″ × 3.5″, not 2″ × 4″.
Historical reason: Originally, rough-cut lumber fresh from the sawmill did measure 2″ × 4″. However, the lumber then went through drying (removing moisture) and planing (smoothing surfaces), which reduced dimensions by approximately 1/4″ on each face. Rather than rename everything, the industry kept nominal sizing for ordering convenience while standardizing actual dimensions.
Standard actual dimensions:
- 2×4 → 1.5″ × 3.5″
- 2×6 → 1.5″ × 5.5″
- 2×8 → 1.5″ × 7.25″
- 2×10 → 1.5″ × 9.25″
- 2×12 → 1.5″ × 11.25″
- 4×4 → 3.5″ × 3.5″
- 1×4 → 0.75″ × 3.5″
- 1×6 → 0.75″ × 5.5″
These dimensions are mandated by the American Softwood Lumber Standard (PS 20-20) and are consistent across all retailers.
Why this system persists: Construction is designed around nominal dimensions. Studs are spaced "16 inches on center" in walls, but everyone understands the actual stud is 1.5″ thick. Changing to actual dimension naming would require rewriting building codes, retraining millions of workers, and changing century-old industry conventions.
Important for DIY: Always design projects using actual lumber dimensions, not nominal. If you're building something that needs to be exactly 4 inches wide, a 2×4 laid flat won't work—it's only 3.5 inches.
What is the smallest measurement on a standard tape measure?
Most standard tape measures used in construction and carpentry show markings down to 1/16 inch as the smallest division. Each inch is divided into 16 equal parts, with various line lengths to indicate fractions:
- Longest lines: Every inch (1″, 2″, 3″...)
- Next longest: Half inches (1/2″, 1½″, 2½″...)
- Medium lines: Quarter inches (1/4″, 3/4″, 1¼″...)
- Shorter lines: Eighths (1/8″, 3/8″, 5/8″, 7/8″)
- Shortest lines: Sixteenths (1/16″, 3/16″, 5/16″... through 15/16″)
Precision tape measures for finish carpentry may show 1/32-inch divisions, doubling the number of marks. These are harder to read but provide twice the precision for fine woodworking.
Reading tape measures: The marks use a graduated system where longer marks indicate simpler fractions. The 1/2″ mark is the longest subdivision line, the 1/4″ and 3/4″ marks are slightly shorter, the 1/8″ marks are shorter still, and the 1/16″ marks are the shortest. This visual hierarchy makes it easier to count marks and identify positions quickly without having to count every line.
Practical accuracy: Even with 1/16″ markings, human error in marking and cutting typically limits practical accuracy to about ±1/16″ for construction work. Finish carpentry might achieve ±1/32″ with careful measurement and sharp marking.
For measurements more precise than 1/32 inch, professionals use dial calipers (readable to 0.001″) or digital calipers rather than tape measures.
Conversion Table: Centimeter to Inch
| Centimeter (cm) | Inch (in) |
|---|---|
| 0.5 | 0.197 |
| 1 | 0.394 |
| 1.5 | 0.591 |
| 2 | 0.787 |
| 5 | 1.969 |
| 10 | 3.937 |
| 25 | 9.843 |
| 50 | 19.685 |
| 100 | 39.37 |
| 250 | 98.425 |
| 500 | 196.85 |
| 1,000 | 393.701 |
People Also Ask
How do I convert Centimeter to Inch?
To convert Centimeter to Inch, enter the value in Centimeter in the calculator above. The conversion will happen automatically. Use our free online converter for instant and accurate results. You can also visit our length converter page to convert between other units in this category.
Learn more →What is the conversion factor from Centimeter to Inch?
The conversion factor depends on the specific relationship between Centimeter and Inch. You can find the exact conversion formula and factor on this page. Our calculator handles all calculations automatically. See the conversion table above for common values.
Can I convert Inch back to Centimeter?
Yes! You can easily convert Inch back to Centimeter by using the swap button (⇌) in the calculator above, or by visiting our Inch to Centimeter converter page. You can also explore other length conversions on our category page.
Learn more →What are common uses for Centimeter and Inch?
Centimeter and Inch are both standard units used in length measurements. They are commonly used in various applications including engineering, construction, cooking, and scientific research. Browse our length converter for more conversion options.
For more length conversion questions, visit our FAQ page or explore our conversion guides.
Helpful Conversion Guides
Learn more about unit conversion with our comprehensive guides:
📚 How to Convert Units
Step-by-step guide to unit conversion with practical examples.
🔢 Conversion Formulas
Essential formulas for length and other conversions.
⚖️ Metric vs Imperial
Understand the differences between measurement systems.
⚠️ Common Mistakes
Learn about frequent errors and how to avoid them.
All Length Conversions
Other Length Units and Conversions
Explore other length units and their conversion options:
- Meter (m) • Centimeter to Meter
- Kilometer (km) • Centimeter to Kilometer
- Hectometer (hm) • Centimeter to Hectometer
- Decimeter (dm) • Centimeter to Decimeter
- Millimeter (mm) • Centimeter to Millimeter
- Foot (ft) • Centimeter to Foot
- Yard (yd) • Centimeter to Yard
- Mile (mi) • Centimeter to Mile
- Nautical Mile (NM) • Centimeter to Nautical Mile
- Micrometer (μm) • Centimeter to Micrometer
Verified Against Authority Standards
All conversion formulas have been verified against international standards and authoritative sources to ensure maximum accuracy and reliability.
National Institute of Standards and Technology — Official US standards for length measurements
Bureau International des Poids et Mesures — International System of Units official documentation
Last verified: December 3, 2025